粉碎程度：
細粉碎單位能耗：
·產量：
最小15 kg帶球模塊 / 最小 20 kg 桿模塊裝機功率（kw）：
0.75KW成品細度：
< 100 μm with ball module / 2,100 μm with rod module入料粒度（mm）：
< 3.35 mm 球模塊 / 12.50 mm 棒模塊看了球和棒磨機的用戶又看了
留言詢價
虛擬號將在 180 秒后失效
使用微信掃碼撥號
detailed overview and knowledge of the characteristics of a raw
material is of utmost importance, especially when planning the layout of
a crushing plant. In order to minimize all possible risks extensive
trials are necessary to obtain information on the properties of the raw
materials . A clear definition of the required crushing capacities and
the desired product quality can be precisely determined by using the
Bond Index test methods. Using the Bond Index test procedures it is
possible to calculate crushing / abrasion behavior of mineral samples.
This knowledge is essential to define the required ball mill layout and
production capacity.
In order to perform the Bond Index Test successfully it is necessary to use pre-crushed sample material as defined below:
Module Ball Mill
Minerals pre-crushed to < 3.35 mm and sieved
Drillcore pre-crushed to < 3.35 mm and sieved
Half Drillcore pre-crushed to < 3.35 mm and sieved
The Bond Index conforming ball charge consists of:
43 x 1.45” balls
67 x 1.17” balls
10 x 1” balls
71 x 0.75” balls
94 x 0.61” balls
The optimum number of grinding balls is 285. However, the ball diameters
vary due to wear. Therefore, the total ball number should be adjusted
from time to time to ensure a total mass of 20.125 grams.
The grinding jar of the Bond Index Ball Mill measures 12″ x 12″ and has well-rounded corners.
Module Rod Mill
Minerals pre-crushed to < 12.50 mm and sieved
Drillcore pre-crushed to < 12.50 mm and sieved
Half a drillcore pre-crushed to < 12.50 mm and sieved
The Bond Index conforming rod charge consists of:
6 rods of 1.25“ diameter and 21“ length
2 rods of 1.75“ diameter and 21“ length
The grinding jar for the Bond Index Rod Mill is 12″ x 24″ in size and has a wave-shaped design.
At
least 15 to 20 kg sample material is required to simulate a closed
grinding circuit in a ball or rod mill. The Rod Mill Work Index (RWI)
is used for particle size determination in a size range from 25 mm down
to 2.1 mm whereas Ball Mill Work Index (BWI) is used for the range from
2.1 mm down to 100 μm.
Adjustment of grinding parameters:
The
operation display permits convenient selection and storage of
parameters such as rotation counter, rotation speed, grinding time,
start and stop.
適合定義功指數
可選球磨和棒磨
易傾斜空鼓
固體鋼鐵結構
可移動樣品收集裝置
便捷的數據顯示
帶手柄漏斗
符合人體工學的導軌利于移除研磨罐
分離網格將樣品和研磨球分開（僅限研磨球）
帶墊片研磨罐用于無損耗操作
固體防噪音罩帶安全開關
緊急開關
| 應用 | 礦石和礦物質量化的易磨性 |
| 應用領域 | 地質 / 冶金, 建筑原料, 環(huán)境 / 資源回收利用 |
| 樣品特征 | 硬的, 脆性的 |
| 粉碎原理： | friction |
| **進樣尺寸 | < 3.35 mm 球模塊 / 12.50 mm 棒模塊 |
| *終出料粒度 * | < 100 μm with ball module / 2,100 μm with rod module |
| 批次加料量* | *小15 kg帶球模塊 / *小 20 kg 桿模塊 |
| 旋轉速度 | 70 min-1 球模塊 / 46 min-1 棒模塊 |
| 研磨平臺數 (可接納研磨罐數) | 1 |
| 研磨套件材料： | 硬質剛 |
| 研磨罐尺寸 | 21.7 l 球模塊 / 43.3 l 棒模塊 |
| 粉碎時間設定 | 數字模式 |
| 驅動功率 | 0.75 kW |
| 電源數據： | 不同電壓 |
| 電源接頭： | 單相 |
| 防護類型 | IP 50 |
| 機體尺寸（寬x高x縱深） | 1500 x 1200 x 700 mm |
| 凈重 | ~ 295 kg |
| 標準 | CE |
Please note:
受樣品材料性質和儀器配置/設定的影響
球和棒磨機主要有相同的概念包括一個12 x12“帶球的罐或12 x24 ”罐和研磨棒。
研磨罐放到一個電機驅動旋轉的支架，有三種擺放方式：:向上加載，水平研磨，向下排出。
進行邦德功指數測試需要用到已知的研磨球或研磨棒，電子控制集成的驅動器配有過載保護和許可和控制不同的速度。
在磨削過程中球/棒運動和研磨罐的速度差產生相互作用和影響的摩擦力,釋放出所需的粉碎能量。這些力量之間的相互作用產生有力的粉碎效果。
根據技術改造和誤差調整
適合定義功指數
可選球磨和棒磨
易傾斜空鼓
固體鋼鐵結構
可移動樣品收集裝置
便捷的數據顯示
帶手柄漏斗
符合人體工學的導軌利于移除研磨罐
分離網格將樣品和研磨球分開（僅限研磨球）
帶墊片研磨罐用于無損耗操作
固體防噪音罩帶安全開關
緊急開關
球和棒磨機的工作原理介紹？球和棒磨機的使用方法？球和棒磨機多少錢一臺？球和棒磨機使用的注意事項球和棒磨機的說明書有嗎？球和棒磨機的操作規(guī)程有嗎？球和棒磨機的報價含票含運費嗎？球和棒磨機有現貨嗎？球和棒磨機包安裝嗎？
手機版：
工商已核實
